有砟轨道路基翻浆冒泥模型试验系统的研发与应用

为研究既有线有砟轨道路基的翻浆冒泥机理，自主研发了一套能够模拟循环荷载–湿化耦合作用的模型试验系统。模型试样直径500 mm，由厚度分别为350 mm的路基土和200 mm的道砟组成，整个试样在高强度透明有机玻璃模型筒中制备完成。模型试验系统配备有监测荷载、位移、体积含水率和孔隙水压力的4种传感器，并通过高清相机对颗粒迁移过程进行图像捕捉。基于所研发的试验系统，针对辛泰铁路典型翻浆冒泥病害路段土样，开展翻浆冒泥模型试验。试验结果表明：动孔隙水压力是导致翻浆冒泥病害产生的关键因素。随着体积含水率的增加，动孔隙水压力引起的颗粒迁移量逐渐增加；在饱和状态下，会引起大量颗粒迁移，翻浆冒泥现象显著。试验结束时，道砟污染指数达到25%，在实际工程中已严重影响铁路的正常运营，有必要对污染道砟进行换填。     

双功能催化剂上四氢萘加氢裂化生成单环芳烃的反应网络研究

Conversion of LCO (light cycle oil) to BTX (benzene, toluene, and xylene) is an economically valuable method for refineries. However, this approach still faces difficulties as the main reactions are not clearly understood. Here we study the detailed hydrocracking pathway of typical reactants, 1-methylnaphthalene and tetralin, through molecular simulations and experiments to improve our understanding of the conversion process of LCO to BTX. Molecular simulations demonstrate that the rate-determining step is the isomerization pathway of six-membered ring to five-membered ring in tetralin as its activation energy (ΔEa) is the highest among all the reactions and the order of ΔEa of reactions is isomerization > ring-opening ≈ side-chain cleavage. The results of experiments show that with the increase in reaction depth, i.e., through a high temperature (350 – 370 °C) and low LHSV (4.5 – 6.0 h−1), isomerization, ring-opening, and side-chain  cleavage reactions occurred, thus improving the selectivity and yield of alkyl aromatics.     

倾斜入射下的单截面平面度绝对检验

针对大尺寸光学平面的直线度的纳米级测量精度需求，提出了倾斜入射下单截面平面度绝对检验方法，实现了对超过相移干涉仪口径的长平晶绝对检验。利用棱镜转向实现倾斜入射角度的精密预标定，棱镜标定角度的精度高于圆光栅和图像分析等方法，可提高测量不确定度到0.0042 μm。对比了常规三面互检绝对检验结果与本方法的差异，在相同尺寸下，直线度误差仅为1.2 nm。在确认标定反射镜位置后，整个倾斜入射的干涉图调整过程将被完全集中到待测长平晶的工作面上，不需要再对反射平晶进行操作。调整长平晶时各个维度的操作互不干涉，可快速简便地得到测量结果。     

火花放电原子发射光谱类型标准化校正方式的探讨

在国内,火花放电原子发射光谱分析广泛使用类型标准化进行方法校正。在国外,标准和文献中鲜见使用此方法的相关论述。类型标准化主要采用平移校正和转动校正两种方式,哪种方式更加合理也鲜见报道。国外设备类型标准化的默认设置优先采用转动校正方式,相关国内标准对最优校正方式的规定尚不明确,此默认设置的合理性有待探讨。实验选用低合金钢20CrNi2Mo、R407标准样品和不锈钢317L、0Cr18Ni9标准样品,引用国内相关标准,以正确度临界差为评判依据,模拟类型标准化样品和待测样品“十分接近”和“接近”两种情况下平移校正和转动校正的数据正确度。经数据统计分析,平移校正分析结果均满足要求,转动校正结果在“接近”情况下部分元素不满足要求。结合相关国家标准中元素含量范围和精密度数据进行分析,通过计算允许最大偏倚量并制作曲线图方式展开分析,得出如下结论:在满足文中类型标准化控制要点前提下,分析设置更适合于采用平移校正方式。     

聚合物对旋流器内油滴聚结与分离效率的影响

为了研究聚合物对水力旋流器内油滴聚结与分离效率的影响规律,以螺旋导流内锥式旋流器为研究对象,利用群体平衡模型(PBM)方法对不合聚与含聚0.5‰工况下油水两相在旋流器内的速度场、黏度场、油滴聚结、运移特性及分离效率进行数值分析,并通过实验验证.结果 表明:聚合物的加入增大了水相黏度,使油滴在旋流器内最大停留时间与轴向运动距离增加,增加了油滴碰撞聚结的机会,但降低轴心处油滴向上运动的轴向速度,使油滴无法快速从溢流口流出,最终从底流口流出,增加油水分离的难度.与不合聚时相比,含聚0.5‰工况下,轴心处的油滴粒径与含油体积分数较高,但简化分离效率由99.79％降低至94.72％.通过马尔文粒度仪对两种工况下入口与出口的油滴粒径进行测试,含聚0.5‰时溢流与底流口油滴粒径高于不合聚时,验证了模拟的准确性.     

Research on phase shift characteristics of electromagnetic wave in plasma

The phase shift characteristics reflect the state change of electromagnetic wave in plasma sheath and can be used to reveal deeply the action mechanism between electromagnetic wave and plasma sheath. In this paper, the phase shift characteristics of electromagnetic wave propagation in plasma were investigated. Firstly, the impact factors of phase shift including electron density,collision frequency and incident frequency were discussed. Then, the plasma with different electron density distribution profiles were employed to investigate the influence on the phase shift characteristics. In a real case, the plasma sheath around the hypersonic vehicle will affect and even break down the communication. Based on the hypersonic vehicle model, we studied the electromagnetic wave phase shift under different flight altitude, speed, and attack angle. The results indicate that the phase shift is inversely proportional to the flight altitude and positively proportional to the flight speed and attack angle. Our work provides a theoretical guidance for the further research of phase shift characteristics and parameters inversion in plasma.